ayf53 ordering information product types notes: 1. order unit; for mass production: in 1-inner carton (1-reel) units samples for mounting check: in 50-connector units. please contact our sales of?e. 2. please contact are sales of?e for connectors having a number of contacts other than those listed above. 0.5 mm pitch, back lock structure fpc connectors y5b/y5bw (0.5 mm pitch) height y5b y5bw pac king number of contacts pa rt number number of contacts pa rt number inner carton (1-reel) outer carton 1.0 mm 4a yf530435 2 ayf530265 5,000 pieces 10,000 pieces 6 ayf530635 4 AYF530465 8a yf530835 6 ayf530665 10 ayf531035 8 ayf530865 12 ayf531235 10 ayf531065 24 ayf532435 22 ayf532265 50 ayf535035 48 ayf534865 new features ?low pro?e, space saving back lock type with improved lever operability ?mechanical design freedom achieved by top and bottom double contacts ?low pro?e, space saving design with a wide selection, including a type with a small number of contacts low pro?e and space saving body of 1.0 mm high and 3.20 mm deep (3.70 mm including the lever) y5b and y5bw can have a minimum of four and two contacts respectively, contributing to the miniaturization and thickness reduction of target equipment. ?wiring patterns can be located underneath the connector. ?man-hours for assembly can be reduced by delivering the connectors with their levers opened. ?y5bw features advanced functionality, including a structure to temporarily hold the fpc and a higher holding force. the fpc holding contacts located on both ends of the connector facilitate positioning of fpc and further enhance the fpc holding force. applications a wide range of digital equipment, including mobile phones, pcs, dscs, and dvcs. ideal for their touch panels and lcd backlights, which require connectors with a small number of contacts. y5b y5bw compliance with rohs directive unit: mm 1.00 3.20 4 contacts (y5b: minimum) applicable fpc shapes with through-holes with notches structure to lock through-holes and notches on both ends of the fpc with holding contacts (1) the holding contacts lock the fpc by its through-holes or notches, allowing users to confirm the completion of the fpc insertion operation. (2) the inserted fpc can be temporarily held until the lever is closed. (3) when the lever is closed, the holding contacts lock the fpc by its through-holes and notches, enhancing the fpc holding force. 53: fpc connector 0.5 mm pitch (back lock) ayf 5 3 5 number of contacts (2 digits) function 3: top and bottom double contacts (y5b) 6: top and bottom double contacts, lock holding type (y5bw) surface treatment (contact portion / terminal portion) 5: au plating/au flash plating (ni barrier) panasonic-electric-works.net/ac panasonic-electric-works.net/ac panasonic-electric-works.net/ac
ayf53 specifications 1. characteristics 2. material and surface treatment dimensions (unit: mm) item speci?ations conditions electrical characteristics rated current 0.5a/contact rated voltage 50v ac/dc insulation resistance min. 1,000m ? (initial) using 250v dc megger (applied for 1 min.) breakdown voltage 250v ac for 1 min. no short-circuiting or damage at a detection current of 1 ma when the speci?d voltage is applied for one minute. contact resistance max. 80m ? based on the contact resistance measurement method speci?d by jis c 5402. mechanical characteristics fpc holding force y5b: min. 0.2n/contacts contacts (initial) y5bw: min. 0.2n/contacts contacts + 2.0n (initial) measurement of the maximum force applied until the inserted compatible fpc is pulled out in the insertion axis direction while the connector lever is closed contact holding force min. 0.2n/contacts y5b: measuring the maximum force. as the contact is axially pull out. y5bw: measuring the maximum force. as the contact and holding terminal are axially pull out. soldering terminal holding force min. 0.2n/contacts measuring the maximum force. as the soldering terminal is axially pull out. environmental characteristics ambient temperature ?5 c to +85 c no freezing at low temperatures. no dew condensation. storage temperature ?5c to +85 c (product only) ?0c to +50 c (emboss packing) thermal shock resistance (with fpc inserted) 5 cycles, insulation resistance min. 100m ?, contact resistance max. 100m ? sequence 1. ?5 c, 30 minutes 2. ~ , max. 5 minutes 3. 85 c, 30 minutes 4. ~ , max. 5 minutes humidity resistance (with fpc inserted) 120 hours, insulation resistance min. 100m ?, contact resistance max. 100m ? bath temperature 40 2c, humidity 90 to 95% r.h. saltwater spray resistance (with fpc inserted) 24 hours, insulation resistance min. 100m ?, contact resistance max. 100m ? bath temperature 35 2c, saltwater concentration 5 1% h 2 s resistance (with fpc inserted) 48 hours, contact resistance max. 100m ? bath temperature 40 2c, gas concentration 3 1 ppm, humidity 75 to 80% r.h. soldering heat resistance peak temperature: 260 c or less re?w soldering 300 c within 5 sec. 350 c within 3 sec. soldering iron lifetime characteristics insertion and removal life 20 times repeated insertion and removal: min. 10 sec./time unit weight y5b (50 contacts): 0.16 g pa rt name material surface treatment molded portion housing: lcp resin (ul94v-0) lever: lcp resin (ul94v-0) contact copper alloy contact portion; base: ni plating, surface: au plating te r minal portion; base: ni plating, surface: au plating holding contact portion copper alloy terminal portion; base: ni plating, surface: au plating soldering terminal portion copper alloy base: ni plating, surface: au plating 0 ? 3 + 3 0 0.500.10 b0.20 c0.20 1.000.10 (1.76) (0.32) a te rm inal coplanarity 0.1 (contact and soldering terminal) (3.70) (0.30) (0.15) (0.15) 2.90 3.20 (0.50) (1.50) (fpc insertion depth) y5b number of contacts/ dimension a b c 4 4.00 3.36 1.50 6 5.00 4.36 2.50 8 6.00 5.36 3.50 10 7.00 6.36 4.50 12 8.00 7.36 5.50 24 14.00 13.36 11.50 50 27.00 26.36 24.50 panasonic-electric-works.net/ac
ayf53 embossed tape dimensions (unit: mm) (common for respective contact type) 2.50 min. (reinforcing plate) 1.50 min. (exposed part of the conductor) (a+1)0.05 a0.03 0.300.03 r0.20 0.500.07 0.500.03 (fpc) 0.350.03 (ffc) 0.300.03 y5b recommended fpc/ffc dimensions the conductive parts should be based by ni plating and then au plating. number of contacts/ dimension a 4 1.50 6 2.50 8 3.50 10 4.50 12 5.50 24 11.50 50 24.50 0.500.10 b0.20 c0.20 1.000.10 (1.76) (0.32) a c te rm inal coplanarity (3.70) (0.30) (0.15) (0.15) 2.90 3.20 (0.50) (1.50) (fpc insertion depth) 0.1 (contact, holding contact and soldering terminal) y5bw number of contacts/ dimension a b c 2 4.00 3.36 1.50 4 5.00 4.36 2.50 6 6.00 5.36 3.50 8 7.00 6.36 4.50 10 8.00 7.36 5.50 22 14.00 13.36 11.50 48 27.00 26.36 24.50 r0.20 r0.20 r0.20 2.50 min. (reinforcing plate) 2.50 min. (reinforcing plate) 1.50 min. (exposed part of the conductor) 1.50 min. (exposed part of the conductor) (a+2)0.05 1.000.07 0.50 0.03 (pitch) 0.350.03 0.300.03 0.300.03 0.800.05 1.300.10 1.050.05 a0.03 (a+2)0.05 0.50 0.03 (pitch) 0.350.03 a0.03 notches type through-holes type +0.03 ?.05 0.70 +0.07 ?.06 1.00 +0.03 ?.05 0.45 must not reach the conductor r0.20 +0.03 ?.05 0.50 (through-hole) dia. must not reach the conductor y5bw recommended fpc dimensions the conductive parts should be based by ni plating and then au plating. number of contacts/ dimension a 2 0.50 4 1.50 6 2.50 8 3.50 10 4.50 22 10.50 48 23.50 ?speci?ations for taping (in accordance with jis c 0806-1990. however, not applied to the mounting-hole pitch of some connectors.) ?speci?ations for the plastic reel (in accordance with eiaj et-7200b.) (a0.3) a: max. 24 mm tape i (a0.3) (c) (b) a: 44 mm tape ii (2.0) 8.0 (4.0) (2.0) (8.0) (4.0) (1.75) (1.75) (b) leading direction after packaging 1.50 dia. +0.1 0.0 1.50 dia. +0.1 0.0 embossed mounting-hole taping reel top cover tape label embossed carrier tape 380 dia. (d1) panasonic-electric-works.net/ac
ayf53 ?y5b dimension table (unit: mm) ?y5bw dimension table (unit: mm) ?connector orientation with respect to embossed tape feeding direction notes number of contacts type of taping a b c d quantity per reel 4, 6, 8, and 10 contacts tape i 16.0 7.5 17.4 5,000 12 and 24 contacts tape i 24.0 11.5 25.4 5,000 50 contacts tape ii 44.0 20.2 40.4 45.4 5,000 number of contacts type of taping a b c d quantity per reel 2, 4, 6, and 8 contacts tape i 16.0 7.5 17.4 5,000 10 and 22 contacts tape i 24.0 11.5 25.4 5,000 48 contacts tape ii 44.0 20.2 40.4 45.4 5,000 type direction of tape progress y5b y5bw 1. recommended pc board and metal mask patterns appropriate control of solder amount is required to minimize solder bridges and other defects for connectors with 0.3 mm or 0.5 mm pitch terminals, which require high-density mounting. refer to the recommended pc board pattern. ?y5b ?y5bw 2. precautions for insertion/removal of fpc do not apply an excessive load to the lever in the opening direction beyond its open position; otherwise, the lever may be deformed or removed. do not open/close the lever without an fpc inserted; otherwise, the terminals may be deformed, and the fpc insertion force may increase. do not apply an excessive load to the lever in a direction perpendicular to the lever rotation axis or in the lever opening direction; otherwise, the terminals may be deformed, and the lever may be removed. these connectors are of the back lock type, which has the fpc insertion section on the opposite side of the lever. be careful not to make a mistake in the fpc insertion position or the lever opening/closing position. otherwise, a contact failure or connector breakage may occur. these connectors have top and bottom double contacts. do not insert an fpc upside down. inserting an fpc in a direction opposite to that you intended may cause an operation failure or malfunction. fully open the lever to insert an fpc. completely insert the fpc horizontally. an fpc inserted at an excessive angle to the board may cause the deformation of metal parts, fpc insertion failures, and fpc circuit breakages. insert the fpc to the full depth of the connector without altering the angle. to close the lever, turn down the lever by pressing the entire lever or both sides of the lever with the balls of ?gers. be careful. if pressure to the lever is applied unevenly, such as to an edge only, it may deform or break. also, make sure that the lever is closed completely. not doing so will cause a faulty connection. av oid applying an excessive load to the top of the lever during or after closing the lever. otherwise, the terminals may be deformed. when opening the lever to remove the fpc, ensure that the lever will not go over the initial position; otherwise, the lever may be removed. remove the fpc at parallel with the lever fully opened. if the lever is closed, or if the fpc is forcedly pulled, the product or fpc may break. if a lever is accidentally detached during the handling of a connector, do not use the connector any longer. after an fpc is inserted, carefully handle it so as not to apply excessive stress to the base of the fpc. 3. cautions for using y5bw the holding contacts cannot be used as conductors. the holding contacts are located on both ends of the contacts, and the shape of the soldered portions is the same as that of the other contacts. therefore, be careful to avoid any confusion. number of contacts/ dimension c d 4 1.50 3.10 6 2.50 4.10 8 3.50 5.10 10 4.50 6.10 12 5.50 7.10 24 11.50 13.10 50 24.50 26.10 number of contacts/ dimension c d 2 1.50 3.10 4 2.50 4.10 6 3.50 5.10 8 4.50 6.10 10 5.50 7.10 22 11.50 13.10 48 24.50 26.10 for other cautions, please refer to the last page. recommended pc board pattern (mount pad arrangement pattern) (top view) connector outline (lever opened) te r minal soldering terminal 3.300.05 0.800.05 0.800.05 d0.10 0.400.05 c0.05 0.500.05 0.300.05 contact holding contact connector outline (lever opened) soldering terminal 3.300.05 0.800.05 0.800.05 0.400.05 recommended pc board pattern (mount pad arrangement pattern) (top view) c0.05 0.500.05 0.300.05 d0.10 panasonic-electric-works.net/ac
fpc connector selector chart 0.2a/contact 50v ac/dc 20 times 0.5mm pitch type t ypes product name part no. shape features lock structure contact structure contact pitch compatibility with fpc/ffc t erminal pitch 0.9mm 0.9mm 0.6mm 0.3mm front lock 0.3mm front lock back lock slide lock front lock 0.6mm 0.9mm 0.3mm 0.6mm bottom contact bottom contact bottom contact bottom contact top and bottom double contacts top and bottom double contacts 1.9mm 1.0mm 0.5mm 0.5mm 0.5mm fpc/ffc fpc/ffc fpc/ffc fpc fpc fpc fpc 0.5mm 2.0mm 0.5mm 0.5mm mounting height dimensions (short width) rohs directive t erminal shape insertion and removal life ambient temperature rated voltage rated current no. of contacts 10 20 30 40 50 60 51 41 45 31 33 35 39 23 25 27 29 15 17 51 41 45 45 31 33 35 39 31 33 35 39 21 23 25 27 23 25 27 29 15 17 7 9 11 13 15 17 46 810 12 24 68 10 40 45 34 26 28 51 50 54 24 24 50 22 48 15 0.2a/contact 50v ac/dc smd smd smd smd smd 30 times 1 5 10 0.3mm pitch type y3ft 3.2mm (including lever) 3.0mm 3.2mm (including lever) 3.0mm 3.15mm (including lever) 2.95mm 5.2mm (including lever) 4.0mm 3.7mm (including lever) 3.2mm 6.3mm (including lever) 5.4mm ayf31 ?? 15 ayf32 ?? 15 ayf33 ?? 35 ayf51 ?? 15 ayf53 ?? 65 ayf53 ?? 35 ayf52 ?? 15 y3f y3b y5f y5b y5bw y5s compliance 0.2a/contact 50v ac/dc 30 times compliance compliance compliance 0.5a/contact 50v ac/dc 20 times smd compliance 0.5a/contact 50v ac/dc 30 times compliance 0.5a/contact 50v ac/dc 30 times back lock fpc connector selector chart a wide variety of digital equipments slide lock structure soldering terminals (metal clips) resistant to twisting fpc/ffc (au contact) are also av ailable low profile, space saving back lock type with improved lever operability the lineup includes a type with a small number of contacts. top and bottom double contacts structure y5bw features advanced functionality a wide variety of digital equipments front lock structure soldering terminals (metal clips) resistant to twisting fpc/ffc (au contact) are also av ailable low-profile, space-saving design (pitch: 0.3 mm) compatible with fpc with tabs, reliability is increased through secure connectibility wiring patterns can be located underneath the connector low-profile, space-saving design (3.0mm pitch) compatible with fpc without tabs, allowing smooth fpc insertion wiring patterns can be located underneath the connector the world's slimmest* and low profile design (pitch: 0.3 mm) mechanical design freedom achieved by top and bottom double contacts wiring patterns can be located underneath the connector ?5c to +85c ?5c to +85c ?5c to +85c ?5c to +85c ?5c to +85c ?5c to +85c panasonic-electric-works.net/ac
fpc connector selector chart 0.2a/contact 50v ac/dc 20 times 0.5mm pitch type t ypes product name part no. shape features lock structure contact structure contact pitch compatibility with fpc/ffc t erminal pitch 0.9mm 0.9mm 0.6mm 0.3mm front lock 0.3mm front lock back lock slide lock front lock 0.6mm 0.9mm 0.3mm 0.6mm bottom contact bottom contact bottom contact bottom contact top and bottom double contacts top and bottom double contacts 1.9mm 1.0mm 0.5mm 0.5mm 0.5mm fpc/ffc fpc/ffc fpc/ffc fpc fpc fpc fpc 0.5mm 2.0mm 0.5mm 0.5mm mounting height dimensions (short width) rohs directive t erminal shape insertion and removal life ambient temperature rated voltage rated current no. of contacts 10 20 30 40 50 60 51 41 45 31 33 35 39 23 25 27 29 15 17 51 41 45 45 31 33 35 39 31 33 35 39 21 23 25 27 23 25 27 29 15 17 7 9 11 13 15 17 46 810 12 24 68 10 40 45 34 26 28 51 50 54 24 24 50 22 48 15 0.2a/contact 50v ac/dc smd smd smd smd smd 30 times 1 5 10 0.3mm pitch type y3ft 3.2mm (including lever) 3.0mm 3.2mm (including lever) 3.0mm 3.15mm (including lever) 2.95mm 5.2mm (including lever) 4.0mm 3.7mm (including lever) 3.2mm 6.3mm (including lever) 5.4mm ayf31 ?? 15 ayf32 ?? 15 ayf33 ?? 35 ayf51 ?? 15 ayf53 ?? 65 ayf53 ?? 35 ayf52 ?? 15 y3f y3b y5f y5b y5bw y5s compliance 0.2a/contact 50v ac/dc 30 times compliance compliance compliance 0.5a/contact 50v ac/dc 20 times smd compliance 0.5a/contact 50v ac/dc 30 times compliance 0.5a/contact 50v ac/dc 30 times back lock fpc connector selector chart a wide variety of digital equipments slide lock structure soldering terminals (metal clips) resistant to twisting fpc/ffc (au contact) are also av ailable low profile, space saving back lock type with improved lever operability the lineup includes a type with a small number of contacts. top and bottom double contacts structure y5bw features advanced functionality a wide variety of digital equipments front lock structure soldering terminals (metal clips) resistant to twisting fpc/ffc (au contact) are also av ailable low-profile, space-saving design (pitch: 0.3 mm) compatible with fpc with tabs, reliability is increased through secure connectibility wiring patterns can be located underneath the connector low-profile, space-saving design (3.0mm pitch) compatible with fpc without tabs, allowing smooth fpc insertion wiring patterns can be located underneath the connector the world's slimmest* and low profile design (pitch: 0.3 mm) mechanical design freedom achieved by top and bottom double contacts wiring patterns can be located underneath the connector ?5c to +85c ?5c to +85c ?5c to +85c ?5c to +85c ?5c to +85c ?5c to +85c panasonic-electric-works.net/ac
fpc connectors common cautions for use common cautions for use pc board design design the recommended foot pattern in order to secure the mechanical strength in the soldered areas of the terminal. fpc and equipment design design the fpc based on the recommended dimensions to ensure the required connector performance. in addition, carefully check the equipment design and take required measures for the equipment to prevent the fpc from being removed subsequent to a fall, vibration, or other impact due to the fpc size, weight, or the reaction force of the routed fpc. connector mounting in case the connector is picked up by chucking during mounting, an excessive mounter chucking force may deform the molded or metal part of the connector. consult us in advance if chucking is to be applied. soldering 1) manual soldering. ?due to the low pro?e, if an excessive amount of solder is applied to this product during manual soldering, the solder may creep up to near the contact points, or interference by solder may cause imperfect contact. ?make sure that the soldering iron tip is heated within the temperature and time limits indicated in the speci?ations. ?flux from the solder wire may adhere to the contact surfaces during soldering operations. after soldering, carefully check the contact surfaces and clean off any ?x before use. ?be aware that a load applied to the connector terminals while soldering may displace the contact. ?thoroughly clean the iron tip. 2) re?w soldering ?screen-printing is recommended for printing paste solder. y3ft/y3f/y3b/y5f/y5b/y5bw y5s y3ft/y3f/y3b/y5s/y5b/y5bw ?consult us when using a screen-printing thickness other than that recommended. ?depending on the size of the connector being used, self alignment may not be possible. accordingly, carefully position the terminal with the pc board pattern. ?the recommended re?w temperature pro?e is given in the ?ure below recommended re?w temperature pro?e y3ft/y3f/y3b/y5b/y5bw y5s y5f ?the temperature is measured on the surface of the pc board near the connector terminal. ?some solder and ?x types may cause serious solder creeping. take the solder and ?x characteristics into consideration when setting the re?w soldering conditions. ?when performing re?w soldering on the back of the pc board after re?w soldering the connector, secure the connector using, for example, an adhesive. (double re?w soldering on the same side is possible) 3) reworking on a soldered portion ?finish reworking in one operation. ?for reworking of the solder bridge, use a soldering iron with a ?t tip. do not add ?x, otherwise, the ?x may creep to the contact parts. ?use a soldering iron whose tip temperature is within the temperature range speci?d in the speci?ations. do not drop the product or handle carelessly. otherwise, the terminals may become deformed due to excessive force or the solderability during re?w soldering may degrade. don? open/close the lever or insert/ remove an fpc until the connector is soldered. forcibly applied external pressure on the terminals can weaken the adherence of the terminals to the molded part or cause the terminals to lose their evenness. in addition, do not insert an fpc into the connector before soldering the connector. when cutting or bending the pc board after mounting the connector, be careful that the soldered sections are subjected to excessive forces. other notes when coating the pc board after soldering the connector to prevent the deterioration of insulation, perform the coating in such a way so that the coating does not get on the connector. the connectors are not meant to be used for switching. to determine the relationship between the screen opening area and the pc board foot pattern area, refer to the diagrams in the recommended patterns for pc boards and metal masks when setting. note that excess solder on the terminals prevents complete insertion of the fpc, and that excess solder on the metal clips prevents the lever from rotating. note that excess solder inhibits the slider lock operation. screen thickness of 120 m is recom- mended for paste solder printing. te rm inal paste solder pc board foot pattern 150c 180c 230c 220c 200c 260c temperature upper limit (soldering heat resistance) lower limit (solder wettability) preheating peak temperature time 25 sec. 70 sec.60 to 120 sec. 250c 200c 180c 150c time peak temperature preheating 60 to 120 sec. min. 200 c, 70 sec. te mperature 260c 200c 180c 150c time peak temperature preheating 60 to 120 sec. min. 200 c, 70 sec. te mperature f or other details, please verify with the product speci?ation sheets. do not the soldered areas to be subjected to forces panasonic-electric-works.net/ac
|
